Code Confidencebuild 3.0.0.201402161939

CDL Commands

There are four CDL-related commands which can occur at the top-level of a CDL script: cdl_package, cdl_component, cdl_option and cdl_interface. These correspond to the basic building blocks of the language (CDL interfaces are described in the Section called Interfaces). All of these take the same basic form:

cdl_package <name> {
    …
}

cdl_component <name> {
    …
}

cdl_option <name> {
    …
}

cdl_interface <name> {
    …
}

The command is followed by a name and by a body of properties, the latter enclosed in braces. Packages and components can contain other entities, so the cdl_package and cdl_component can also have nested commands in their bodies. All names must be unique within a given configuration. If say the C library package and a TCP/IP stack both defined an option with the same name then it would not be possible to load both of them into a single configuration. There is a naming convention which should make accidental name clashes very unlikely.

It is possible for two packages to use the same name if there are no reasonable circumstances under which both packages could be loaded at the same time. One example would be architectural HAL packages: a given eCos configuration can be used on only one processor, so the architectural HAL packages CYGPKG_HAL_ARM and CYGPKG_HAL_I386 can re-use option names; in fact in some cases they are expected to.

Each package has one top-level CDL script, which is specified in the packages ecos.db database entry. Typically the name of this top-level script is related to the package, so the kernel package uses kernel.cdl, but this is just a convention. The first command in the top-level script should be cdl_package, and the name used should be the same as in the ecos.db database. There should be only one cdl_package command per package.

The various CDL entities live in a hierarchy. For example the kernel package contains a scheduling component, a synchronization primitives component, and a number of others. The synchronization component contains various options such as whether or not mutex priority inheritance is enabled. There is no upper bound on how far components can be nested, but it is rarely necessary to go more than three or four levels deeper than the package level. Since the naming convention incorporates bits of the hierarchy, this has the added advantage of keeping the names down to a more manageable size.

The hierarchy serves two purposes. It allows options to be controlled en masse, so disabling a component automatically disables all the options below it in the hierarchy. It also permits a much simpler representation of the configuration in the graphical configuration tool, facilitating navigation and modification.

By default a package is placed at the top-level of the hierarchy, but it is possible to override this using a parent property. For example an architectural HAL package such as CYGPKG_HAL_SH typically re-parents itself below CYGPKG_HAL, and a platform HAL package would then re-parent itself below the architectural HAL. This makes it a little bit easier for users to navigate around the hierarchy. Components, options and interfaces can also be re-parented, but this is less common.

All components, options and interfaces that are defined directly in the top-level script will be placed below the package in the hierarchy. Alternatively they can be nested in the body of the cdl_package command. The following two script fragments are equivalent:

cdl_package CYGPKG_LIBC {
    …
}

cdl_component CYGPKG_LIBC_STRING {
    …
}

cdl_option CYGPKG_LIBC_CTYPE_INLINES {
    …
}

and:

cdl_package CYGPKG_LIBC {
    …

    cdl_component CYGPKG_LIBC_STRING {
        …
    }

    cdl_option CYGPKG_LIBC_CTYPE_INLINES {
        …
    }
}

If a script defines options both inside and outside the body of the cdl_package then the ones inside will be processed first. Language purists may argue that it would have been better if all contained options and components had to go into the body, but in practice it is often convenient to be able to skip this level of nesting and the resulting behavior is still well-defined.

Components can also contain options and other CDL entities, in fact that is what distinguishes them from options. These can be defined in the body of the cdl_component command:

cdl_component CYGPKG_LIBC_STDIO {

    cdl_component CYGPKG_LIBC_STDIO_FLOATING_POINT {
        …
    }

    cdl_option CYGSEM_LIBC_STDIO_THREAD_SAFE_STREAMS {
        …
    }
}

Nesting options inside the bodies of components like this is fine for simple packages with only a limited number of configuration options, but it becomes unsatisfactory as the number of options increases. Instead it is possible to split the CDL data into multiple CDL scripts, on a per-component basis. The script property should be used for this. For example, in the case of the C library all stdio-related configuration options could be put into stdio.cdl, and the top-level CDL script libc.cdl would contain the following:

cdl_package CYGPKG_LIBC {
    …

    cdl_component CYGPKG_LIBC_STDIO {
        …
        script stdio.cdl
    }
}

The CYGPKG_LIBC_STDIO_FLOATING_POINT component and the CYGSEM_LIBC_STDIO_THREAD_SAFE_STREAMS option can then be placed at the top-level of stdio.cdl. It is possible to have some options nested in the body of a cdl_component command and other options in a separate file accessed by the script property. In such a case the nested options would be processed first, and then the other script would be read in. A script specified by a script property should only define new options, components or interfaces: it should not contain any additional properties for the current component.

It is possible for a component's CDL script to have a sub-component which also has a script property, and so on. In practice excessive nesting like this is rarely useful. It is also possible to ignore the CDL language support for constructing hierarchies automatically and use the parent property explicitly for every single option and component. Again this is not generally useful.

Note: At the time of writing interfaces cannot act as containers. This may change in a future version of the component framework. If the change is made then interfaces would support the script property, just like components.